1255
T
OOLS
Big Twin Mainshaft Seal
Remover & Installer
replaces 95660-42. Use to
install and remove main
seal. This tool will push
seal in as flat and str aight
as possible to .050 below
housing for a no leak fit.
VT No.
Years
Speed
16-1803
1936-76
4
Additional Drivers for Above
16-0702
1977-86
4, (2.4 O.D.)
16-0703
1979-81
5
16-0701
1980-84
5
16-0700
1985-up
5
16-1803
5-Speed Transmission Door Remover & Installer
removes and replaces the door bear ings Saves time
as the complete transmission does not have to be dis-
mounted allowing the mainshaft and countershaft clus-
ters to remain in place for use when installing 5-Speed
Kicker Kit.
VT No.
Item/Brand
16-0756
V-Twin Door Remover &Installer
16-0663
Jims Remover Only
16-0731
Jims Installer Only
16-0672
Bearing Remover/Installer
Jims Big Twin
Mainshaft Primary
Bearing Race
Remover & Installer
for use on all 1984-up
Big Twins, replaces
34902.
VT No. 16-0877
Big Twin 5-Speed
Transmission Shift Pawl
Adjuster Tool Set
fits mid
1992 and later. Includes a tool
to loosen the jam nut on the
pawl adjuster and the other to
adjust the shifter pawl set.
Replaces 41184.
VT No. 16-0646
Jims 5-Speed Transmission Main Drive Gear Tools.
Use 16-0994 to remove and install main drive gear
and install main bearing. Use 16-0718 for remove
main drive bearing. Both tools can be used without
removing transmission case. Use on all 5 or 6-Speed
Big Twins 1980-up.
VT No.
Type
16-0994
Main Drive Gear Installer
16-0718
Main Drive Bearing Remover
16-0663
Mainshaft/Drive Bearing Press Tools.
VT No.
OEM
Fits
Press
16-0105
33428A
79-84 BT 4-spd
Shaft
16-0036
34734
79-90 BT 5-spd
Seal
16-1767
37842
1991-up BT-XL
Drive
16-0731
16-0756
16-0718
16-0994
16-0672
Mainshaft 5 & 6 Speed
Jims Main Bearing Installer Tool.
Allows proper
installation of transmission case main bearing by
holding bearing square to its bore. Use on 2006-up
Dyna and 2007-up FXST-FLT models.
VT No. 16-1355
Jims
Main
Drive
Gear
Installer
Tool.
This tool
will hold
the main drive gear square to its bear ing bore for
proper main drive gear installation. Use on 2006-up
Dyna and 2007-up FXST-FLT models.
VT No. 16-1350
Jims Main Drive Gear Bearing
and Seal Installer.
This tool will
hold bearings and seal square to
its bore for proper installation and
will also allow both to be installed
to proper depth. Use on all 2006-
up Dyna and 2007-up FXST-FLT
models.
VT No. 16-1353
Jims Transmission Door Removal Tool
use this
tool to pull complete door with gears and shafts from
transmission. Use on 2006-up Dyna and 2007-up
FXST-FLT models.
VT No. 16-1358
Jims Right Side Drive Transmission
Trap Door Puller Tool.
Removes access
door on all right side drive transmissions.
VT No. 16-1356
Jims Transmission Main Drive Gear Nut Wrench
Tool.
Use to remove the 2 1/4" hex nut from main
drive gear which secures the rear dr ive trans pulley.
Use with 1/2" drive ratchet. Use on all 2006-up Dyna
and 2007-up FXST-FLT models.
VT No.
Brand
16-1359
Jims
16-1261
Sifton
5-Speed Main Drive Gear
Seal Installer Sets
seal to
proper depth with trans
assembled. By Jims.
VT No. 16-0664
Main Drive Gear Seal Installer
allows installation of main drive gear
oil seal on assembled transmission to
proper depth. The protective sleeve
included is used for protecting inner
bearings of main drive for installation.
For 2006-up FXD and 2007-up FLST.
VT No. 16-1363
16-1261
16-1359
16-0105
16-0036
16-1767
Shifter Shaft Sleeve Tool
fits 5 and 6 Speed tr ans-
mission.
VT No. 16-1664
Countershaft Support Plate Tool
fits
1991-up 5 Speed Sportster.
VT No. 16-1756
Previous Page
